China Slurry Pumps, Warman Pumps and Warman Slurry Pump Parts Manufacutrer in China - Tobee Pump 180 3203 4573

Hydroman Submersible Slurry Pumps with Dry Chamber in Latin America

Mar 31, 2021

Tobee® Hydroman Submersible Slurry Pumps with Dry Chamber. The pump's wetted parts are made of high-alloy wear-resistant material, so the electric slurry pump has good wear resistance and a large flow path.

Design features:
- Submersible pump design, centrifugal.
- In addition to the main impeller, it includes an agitator built into the pump shaft that can move sludge deposited on the bottom of the water in a turbulent flow and pump the sludge out.
- The wetted parts, such as the agitator, are made of high chrome, high hardness cast steel, have wear resistance, corrosion resistance, and high drainage capacity, and allow for the passage of large solid particles.
- The motor is prepared to work submerged in water and also in dry chamber, it has a high sludge suction rate.

Hydroman 200TJQ Submersible Slurry Pumps with Dry Chamber:

Submersible Slurry Pumps with Dry Chamber

Submersible Slurry Pumps with Dry Operation

Submersible Sludge Pumps

Submersible Electric Pumps

Slurry Dredge Pumps

Submersible Electric Pumps with Dry Operation:

● Fluid to be pumped: Sewage sludge
● Brand: Hydroman Pumps
● Model: 200TJQ
● Manufacturer: Hydroman Factory, China
● Flow Rate Offered: 80.0 lps or 1268 gpm (288.0 m3/h)
● Adt Offered: 30.0 meters
● Efficiency: 55%
● Rpm: 1180 rpm (6 poles)
● Engine service factor: 1.2
● Insulation: class H
● Phases / hz / voltage: 3 / 60 / 440
● Discharge diameter: 200mm (8")
● Seal system: Double mechanical seal; immersed in oil.
● Coupling type: Direct
● Maximum particle size: 55 mm
● Percentage of solids by weight: 12%.
● Fluid pH Range: 5 - 12 (Greater range than 6 - 7.7)
● Maximum fluid temperature: 40 °c
● Insulation Class: H
● Specific gravity of the mixture: 1.7 gr/cm3
● Nozzle with water injection: yes, for removal
● Degree of protection: IP68    
● Shaft power: 42.78kw (57.3hp)
● Engine power: 55.0kw (73.7hp
● Drive type: Closed
● Startup type: Direct
Pump casing material: Iron alloy with high chrome content 28% (Hardness 650 BHN) - Better than ductile iron.
● Superior wear plate: 28% high chrome iron alloy (650 BHN hardness)
● Bottom Wear Plate: High Chrome 28% Iron Alloy (Hardness 650 BHN)
● Shaft material: Chrome steel alloy (40CrMo) of high strength and toughness.

Pump impeller material: 28% high chrome alloy steel (650 BHN hardness)
● Pump agitator material: 28% high chrome alloy steel (650 BHN hardness)
● Motor housing material: Iron alloy with high chrome content 28% (Hardness 650 BHN) - Better than cast iron.
● Type of lubrication: Machine oil; no detergents
● Motor protection: Includes temperature sensors (thermostat) for each coil. Includes humidity sensor, to detect leaks in the oil chamber. Includes relay, for receiving the signal from the sensors.
● Length of submersible cables of force and signal: 20 meters
● Cooling: Internal for dry and wet chamber work
● Flanges: DIN standard

Performance tests will demonstrate compliance with the specified operating point of 80lps, 25m minimum

Submersible Slurry Pump Operation

Submersible Slurry Pump Testing

Technical dept.
Hebei Tobee Pump Co.,Limited

Contact Us

Copyright © 1987-2017 Tobee® Pump. All Rights Reserved

* * *