Professional Slurry Pumps, Warman Pumps and Slurry Pump Parts Manufacutrer in China - Tobee Pump
Sales@tobeepump.com+86 180 3203 4573

Slurry Pump Spare Parts

Aug 29, 2018


WEARING PARTS REPLACEMENTS

The wear rate of a solids handling pump is a function of the severity of the pumping duty and the abrasive properties of the material handled. Therefore, the life of wearing parts, such as impellers and liners, varies from pump to pump and from one installation to another.
Wearing parts must be replaced when the performance of a given pump no longer satisfies the requirements of a particular installation. Where a pump is used on a particular duty for the first time, and especially where failure of a wearing part during service could have serious consequences, Tobee recommends that the pump be opened at regular intervals, parts inspected, and their wear rate estimated so that the remaining life of the parts may be established. For installation of new wearing parts, Pls email to Sales@tobeepump.com


STOCK LEVELS

Spare parts for Warman pumps consist mainly of liners, impellers, bearings, shaft sleeves, seals, and shaft seal parts. Depending on the expected life of each part, you should keep a number of spares of each in stock to ensure a minimum of downtime. Major plants typically stock an additional bearing assembly for every ten (or less) pumps of the same size. This enables a quick exchange of the bearing assembly in any one of the pumps. Often this operation is carried out when wearing parts are being replaced. The removed bearing assembly can then be inspected in a workshop, overhauled if required, and kept ready for the next pump. In this way, damage is prevented and all pumps are always kept in optimum conditions with a minimum of downtime.


PART NUMBERS

Slurry pump parts are described by a part number consisting of three segments.
1. The (1) to (5) digit alpha or alpha/numeric prefix which references the relative pump or frame size of the part.
2. The (3) digit numeric "basic part number" which indicates the part type.
3. The (3) digit alpha/numeric material code.


The following are example part numbers:


BASIC PART No.

STANDARD MATERIAL CODE

PART NAME

001
003
005
011
012
013
026
028
029
032
034
039
041
044
045
060
062
063
064
067
070
073
075
076
078
109
111
117
118
118-1
122 124
125
126
129
130
131
132
134
138
144
179
221
239
292
302
303
306
310
430
-
-

E62
G01
-
E62, E63
E62
D20
E62
A05A
A05A
D20
E62
E63
A05A
K24, C02
E62
R08A
D20
K31, C02
S18
C23
E05
E05
D20
D20
G01
S18
Q05A
E62, C23
K31, C02
P50A
R11A R08A
R08A
E62, C23
E62
E02
A05A
R08A
D20
E62
E62
C23
E02
C23
D20
E02
E02
E02
E02

U04A  



Adjusting Screw
Base
Bearing Assembly
Clamp Washer
Clamp Bolt
Door
Frame Plate Liner /Insert Stud
Expeller
Expeller Ring
Adaptor Plate
Adaptor Plate Bolt
Adaptor Plate Stud
Back Liner
Gland
Gland Bolt
Intake Joint
Labyrinth
Lantern Ring
Impeller O-Ring
Neck Ring
Shaft Key
Shaft
Shaft Sleeve
Shaft Sleeve (Long)
Stuffing Box
Shaft O-Ring
Packing
Shaft Spacer
Lantern Restrictor
Lantern Restrictor (Non-metal)
Expeller Ring/Stuffing Box SealBowl Seal, Door Seal
Bowl Seal, Door Seal
Gland Clamp Bolt
Clamp Ring Bolt
Flange
Bowl
Discharge Joint Ring
Clamp Ring
Grease Cup Adaptor
Back Liner Stud
Shaft Sleeve Spacer
Discharge Flange
Impeller Release Collar
Door Clamp Plate
Lifting Tube
Locating Nut
Shaft Wrench
Stuffing Box/Expeller Ring

Lifting Beam




Warman Slurry Pump Spare Parts

Warman Slurry Pump Rubber Parts


Download in PDF file for slurry pump parts list: Warman parts.pngSlurry Pump Parts Code.pdf


Technical dept.
Hebei Tobee Pump Co.,Limited

Contact Us

Copyright © 1987-2017 Tobee® Pump. All Rights Reserved

* * *
Top